| | | |

Water Filters made EASY at

WATER FILTER FINDER^TM in 0 item(s) in cart / TOTAL: $0.00 View Cart

| | | | |
| | | |

Rusco 1-30CR-F Chemical Resistant Polyester Spin-Down Filter System

30 Mesh/533 Micron, Fits 1" Pipe

Larger View

Rusco Chemically Resistant Spin-Down Sediment Filter with Flush Valve:
The Rusco sediment filter uses centrifugal separation technology to filter sediment from water.
This Rusco filter is made with a Chemically Resistant Screen filter.
High temperature operation up to 200 deg. F (93 deg. C).
The Rusco Chemically Resistant Sediment Filter is made by thermoplastic construction and has high chemical resistance.
The Rusco systems have stainless steel reinforced 3/4" pipe connection.
The Rusco Chemically Resistant filter screen is durable, cleanable and reusable .
The Rusco chemically resistant filters can be used for Hydronic Heating Systems, Industrial Heat Exchangers, Cooling Tower Make Up & Evaporator Water, Domestic or Commercial Hot Water Heaters, and Industrial (Machine Coolant and Cutting Fluids).

Rusco Chemically Resistant Sediment Filter Contaminants:
The Rusco Sediment Filter is designed to remove virtually all types of sediment, including shale, shell, debris, pipe scale, and sand/grit (course, fine, and very fine).
The amount of sediment removed by the Rusco filter screen will depend on the micron rating of the filter screen. Smaller micron rated filter screens will remove smaller particles of sediment from your water.
By removing larger sediment particles from your water, you are preserving the life of appliances and filter cartridges that may be installed after the Rusco sediment filter system.

Rusco 1-30CR-F Chemical Resistant Sediment Filter:
Screen Mesh Size:30
Micron Rating:533
Contaminant Reduction: shale, shell, debris, pipe scale, and sand/grit (course, fine, and very fine)
Inlet/Outlet Pipe Size dimension:1"
Maximum Temperature: 200 degrees F. (93C) at 40 PSI
Minimum Flow Rate For Spin-Down Action: 1 GPM
Maximum Flow Rate: 25 GPM

Materials of Construction:
Body Material: Glass filled polypropylene with 304 stainless steel supporting ring
Cover Material: Chemical and Heat Resistant HP Polymer
Screen Material: Glass filled polypropylene and 304 stainless steel screen
Flush Valve: CPVC
O-Rings: EPDM

Rusco Sediment Filtration System Installation Information:
1. Install the filter in a location that protects it from damage such as impact, freeze, excessive heat, chemical contact and water hammer.
2. Install the filter in the preferred vertical position with the purge outlet pointing down and also where it can be easily accessed for cleaning and maintenance.
3. Install the filter on the discharge side of the pump to allow the filter to be cleaned by purging through the flush valve.
4. Refer to arrows on the filter body for correct water flow direction.
5. Adhere to all local and state codes, laws and regulations.
6. Use approved solvent cement for gluing PVC connections. Follow gluing instructions on glue container. It is recommended that the CLEAR COVER BE REMOVED FROM THE PVC BODY PRIOR TO THE GLUING PROCESS. Any excess glue that comes in contact with the clear cover will damage it.

Rusco Water Filter Screen Change Frequency:
The Rusco filter screens should be cleaned every few months. No tools are required for cleaning.
The filter screen should be replaced every 6-12 months depending on your water usage and water quality.

Rusco Water Filter Screen Cleaning Instructions:
1. The primary method of cleaning the Rusco filter is purging separated solids through the flush valve while the filter is under system pressure. The purging process can be done manually with the flush valve or automated with our optional Automatic Flush Valve.
2. The filter element may need to be removed and cleaned. To remove the filter element, turn off the water supply, drain water pressure, unscrew the clear cover and remove the filter element. Wash off collected sediment by spraying with water. Remove fine particles wedged in the screen with a soft brush. Apply silicone grease to o-rings if needed and reassemble. HAND TIGHTEN ONLY.

Product Code: 1-30CR-F

Reminder

Retail Price
~~$82.17~~

Quantity	Price/Ea.
1 +	$75.00

QTY