- Rusco Stainless Steel Screened Spin-Down Filters with Flush Valve:
- The Rusco clear cover is made of high impact polymer resin for maximum strength and durability. The top of the Rusco system is made of PVC.
- The Rusco sediment filters use centrifugal separation technology to filter sediment from water.
- The Rusco filtration system has a stainless steel screen filter.
- The Rusco filter system's filter screen is cleanable and reusable.
- The Rusco systems have a clear cover that can easily be removed for cleaning. No tools are required to remove the cover.
- Sediment is visible through the clear cover indicating when the filter needs to be flushed.
- Rusco Sediment Filters have an open ball valve to easily flush sediment. When the Rusco filter is full of sediment, simply open the ball valve to flush the sediment.
- Rusco water filtration systems are made from molded non-corrosive materials.
- Rusco Chemically Resistant Sediment Filter Contaminants:
- The Rusco Sediment Filter is designed to remove virtually all types of sediment, including shale, shell, debris, pipe scale, and sand/grit (course, fine, and very fine).
- The amount of sediment removed by the Rusco filter screen will depend on the micron rating of the filter screen. Smaller micron rated filter screens will remove smaller particles of sediment from your water.
- By removing larger sediment particles from your water, you are preserving the life of appliances and filter cartridges that may be installed after the Rusco sediment filter system.
- Rusco Sediment 34-100SS-F Stainless Steel Spin-Down Filter:
- Screen Mesh Size: 100
- Micron Rating: 152
- Contaminant Reduction: shale, shell, debris, pipe scale, and sand/grit (course, fine, and very fine)
- Inlet/Outlet Pipe Size Dimension: .75" FPT
- Maximum Pressure: 150 PSI at 73 degrees F. (23C)
- Maximum Temperature: 100 deg F. at 40 PSI
- Minimum Flow Rate For Spin-Down Action: 1 GPM
- Service Flow Rate: 10 GPM
- Maximum Flow Rate: 20 GPM
- Length: 11-3/8"
- Width: 7-1/4"
- Materials of Construction:
- Body Material: PVC
- Cover Material: High Impact Polymer Resin
- Screen Material: Stainless Steel
- Manufacturer: Rusco 3/4-100SS-F
- Rusco Sediment Filtration System Installation Information:
- 1. Install the filter in a location that protects it from damage such as impact, freeze, excessive heat, chemical contact and water hammer.
- 2. Install the filter in the preferred vertical position with the purge outlet pointing down and also where it can be easily accessed for cleaning and maintenance.
- 3. Install the filter on the discharge side of the pump to allow the filter to be cleaned by purging through the flush valve.
- 4. Refer to arrows on the filter body for correct water flow direction.
- 5. Adhere to all local and state codes, laws and regulations.
- 6. This system connects via female pipe threads. (No glue is needed to connect this system, like other Rusco systems.)
- Rusco Water Filter Screen Change Frequency:
- The Rusco filter screens should be cleaned every few months. No tools are required for cleaning.
- The filter screen should be replaced every 6-12 months depending on your water usage and water quality.
- Rusco Water Filter Screen Cleaning Instructions:
- 1. The primary method of cleaning the Rusco filter is purging separated solids through the flush valve while the filter is under system pressure. The purging process can be done manually with the flush valve or automated with our optional Automatic Flush Valve.
- 2. The filter element may need to be removed and cleaned. To remove the filter element, turn off the water supply, drain water pressure, unscrew the clear cover and remove the filter element. Wash off collected sediment by spraying with water. Remove fine particles wedged in the screen with a soft brush. Apply silicone grease to o-rings if needed and reassemble. HAND TIGHTEN ONLY.