We use cookies to make your experience better.
20 X 2.5 Polypropylene Replacement Filter by Tier1 (5 micron) (6-Pack)
SKU
TIER1_P5_20_6_PACK
Price $25.99 List Price Price $36.99 Save 29%
Availability: In Stock
- Installs quickly and easily
- Provides great tasting, cleaner and fresher water
- Goes to work reducing contaminants for up to six months
- Fits most standard 20 x 2.5-inch housings
The Pentek P5-20 (6-Pack) Comparable Whole House Sediment Water Filter by Tier1 is an ideal solution for filtration needs requiring a 5 micron filter. The Tier1 P5-20 is manufactured to fit standard 20-inch x 2.5-inch filter housings. This product is quick and easy to installs saving you time and money. The P5-20 is designed to reduces contaminants ranging from dirt to sediment and more for up to six months. Order today!
Package Qty | 6 |
---|---|
Used In Brands | Culligan, Pentek, Tier1, Whirlpool |
Manufacturer's Id | P5_20_6_PACK |
UPC | 635510407850 |
Advertised Size (in) | 20 x 2-1/2 |
Actual Size (in) | 20 inches (length) x 2 1/2 inches (outside diameter) |
Actual Size (cm) | 50.8 x 6.35 |
Media | Spun Wound Polypropylene |
Primary Filter Media | Polypropylene |
Filter Life (months) | 36 months |
Micron Rating (Nominal) | 5 |
Operating Temperature (°F) | 40 - 125 |
Operating Temperature (°C) | 4.4 - 51.7 |
Flow Rate (gpm) | 10 |
Flow Rate (lpm) | 37.8541 |
Color | White |
Warranty Guarantee | Unconditional Product Guarantee for Life of the Product |
Reduced Contaminants
The TIER1_P5_20_6_PACK reduces the following contaminants:
- Dirt
- Rust and Corrosion
- Sand
- Sediment
- Silt
The TIER1_P5_20_6_PACK is comparable with the following part numbers
1193047 | 1194282 | 1227868-V | 15-052-03 | ||||
155796-43 | 200144 | 252-050 | 255695 | ||||
255695-43 | 33003033 | 4621-43 | 55410-27 | ||||
93047 | 9320-1143 | 94282 | AP110-2C | ||||
CFS110-C20 | COR205 | COR220 | ED-S-2 | ||||
FPMB-520 | FPMB5-20 | FPMB520 | GX05-20 | ||||
PD-5-20 | PFS205 | PS5-20C | PX05-20 | ||||
SD-25-2005 | SDF-25-2005 | SW5-2 | SWS-20 | ||||
VX05-20 | PENTEK-P5-20 | P5-20 | 155016-43 |
Instructions
- Turn off water supply. Press red pressure-relief button (if present)
- Unscrew housing. Remove large o-ring, wipe clean and set aside
- Discard used filter cartridge. Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly
- Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly
- Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove
- NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove
- Insert new filter cartridge
- Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge
- Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation