X

Save with Auto-Ship

Get the product you need, exactly when you need it, delivered right to your door. No more searching for the right part number, we've got you covered. Plus, you'll save $$ on every order and shipping is on us. Learn more

Save Money

Free Shipping*

Choose Frequency

*Free Shipping available in the contiguous US

Tier1 10 inch x 2.5 inch Pleated Sediment Water Filter (1 Micron)

SKU
TIER1-SPC-25-1001
Price $12.99 List Price Price $18.99 Save 31%
Availability: Discontinued
Choose a quantity
  • 1filter$12.99 
  • 3filters$12.22each
  • 6filters$11.69each
  • Ships fast!
  • Tier1 SPC-25-1001 SPC comparable Series Polyester Water Filters are made for high quality performance
  • Cost effective replacement filter
  • Woven pleated polyester sediment filter
› See more product details
Both bacteria and chemical resistant, the Tier1 10 inch x 2.5 inch pleated sediment water Filter (1 Micron) is perfect for reducing dirt, sand and silt out of your water supply. This filter features a pleated design that allows it to reduce more particles such as sediment and dirt in addition to other particles down to 1 micron in size. In addition this filter is ideal for use in a variety of applications, such as commercial and residential. You can even wash the pleats of this filter, at least once during it's life, for more use . Order today!
More Information
Package Qty 1
Used In Brands Hydronix, Pentek, Tier1
Manufacturer's Id SPC-25-1001
UPC 641945742268
Advertised Size (in) 10 x 2-1/2
Actual Size (in) 9 7/8 inches (length) x 2 1/2 inches (outside diameter)
Actual Size (cm) 25.0825 x 6.35
Outside Diameter (inches) 2.5
Media Non-Woven Pleated Polyester
Materials of Construction Core: Polypropylene, End Caps: Vinyl Plastisol
Filter Life (months) Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x 6 months
Micron Rating (Nominal) The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x 1
Operating Temperature (°F) 40 - 125
Operating Temperature (°C) 4.4 - 51.7
Flow Rate (gpm) Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x 4
Flow Rate (lpm) 15.12
Color White
Warranty Guarantee Unconditional Guarantee for Life of the Product

Reduced Contaminants

The TIER1-SPC-25-1001 reduces the following contaminants:

  • Dirt
  • Particulates
  • Sand
  • Sediment
  • Silt

The TIER1-SPC-25-1001 is comparable with the following part numbers

HYDRONIX-SPC-25-1001
SPC-25-1001
SDF-25-1001
255481-43
FM-1-975

Instructions

  1. Turn off water supply. Press red pressure-relief button (if present)
  2. Unscrew housing. Remove large o-ring, wipe clean and set aside
  3. Discard used filter cartridge
  4. Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly
  5. Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly
  6. Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove
  7. NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove
  8. Insert new filter cartridge
  9. Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge
  10. Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation