X

Save with Auto-Ship

Get the product you need, exactly when you need it, delivered right to your door. No more searching for the right part number, we've got you covered. Plus, you'll save $$ on every order and shipping is on us. Learn more

Save Money

Free Shipping*

Choose Frequency

*Free Shipping available in the contiguous US

10 inch x 2.5 inch Pleated Sediment Water Filter by Tier1 (20 Micron)

SKU
TIER1-SPC-25-1020
Price $9.99 List Price Price $14.99 Save 33%
Availability: Discontinued
9 7/8 inches by 2.5 inches, 20 micron. Fits into filtration systems that use Liquatec SPF-25-1020, Pentek 255483-43 and Watts FM-20-975 water filters
  • Ships fast!
  • Chemical and bacteria resistant sediment filter
  • Greater dirt holding capacity
› See more product details
The 10 inch x 2.5 inch pleated sediment water filter by Tier1 (20 Micron) captures more dirt allowing a longer time between filter changes. This filter is both washable and reusable, the cartridge is a cost effective water filter for residential, commercial and industrial applications and is made with a pleated polyester material that is conveniently bacteria and chemical resistant. Be sure to order your filter today!
More Information
Package Qty 1
Used In Brands Hydronix
Manufacturer's Id SPC-25-1020
UPC 641945742282
Advertised Size (in) 10 x 2-1/2
Actual Size (in) 9 7/8 inches (length) x 2 1/2 inches (outside diameter)
Actual Size (cm) 25.0825 x 6.35
Outside Diameter (inches) 2.5
Media Non-Woven Pleated Polyester
Materials of Construction Core: Polypropylene, End Caps: Vinyl Plastisol
Filter Life (months) Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x 6 months
Micron Rating (Nominal) The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x 20
Operating Temperature (°F) 40 - 125
Operating Temperature (°C) 4.4 - 51.7
Flow Rate (gpm) Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x 10
Flow Rate (lpm) 37.854
Color White
Warranty Guarantee Unconditional Guarantee for the Life of the Product

Reduced Contaminants

The TIER1-SPC-25-1020 reduces the following contaminants:

  • Dirt
  • Particulates
  • Sand
  • Sediment
  • Silt

The TIER1-SPC-25-1020 is comparable with the following part numbers

PENTEK-ECP20-10

The TIER1-SPC-25-1020 fits the following model numbers

CULLIGAN-HF-360

Instructions

  1. Turn off water supply. Press red pressure-relief button (if present)
  2. Unscrew housing. Remove large o-ring, wipe clean and set aside
  3. Discard used filter cartridge
  4. Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly
  5. Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly
  6. Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove
  7. NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove
  8. Insert new filter cartridge
  9. Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge
  10. Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation