X

Save with Auto-Ship

Get the product you need, exactly when you need it, delivered right to your door. No more searching for the right part number, we've got you covered. Plus, you'll save $$ on every order and shipping is on us. Learn more

Save Money

Free Shipping*

Choose Frequency

*Free Shipping available in the contiguous US

Tier1 10 inch x 2.5 inch String Wound Sediment Water Filter (20 Micron)

SKU
TIER1-SWC-25-1020
Price $7.12 List Price Price $10.99 Save 35%
Availability: In Stock
Available Add-Ons

American Plumber, Culligan, Pentek OR-34 O-Ring

Add: $9.99 $6.99
x

Fits into most standard whole house water filtration system housings

SKU: TIER1_REPLACEMENT_KIT_WH25 › See more product details

Tier1 Replacement O-Ring and Lubricant Kit For Whole House Systems Using a 2.5 Inch Replacement Filter

Fits into most standard whole house water filtration system housings
Add: $10.99 $7.99
  • Ships fast!
  • Used in a variety of applications
  • Has a greater dirt holding capacity
› See more product details
  • Ships fast!
  • Used in a variety of applications
  • Has a greater dirt holding capacity
The Tier1 10 inch x 2.5 inch string wound sediment water filter (20 Micron) is the perfect solution if you are looking for quality at a great price. You can use this filter on residential as well as commercial applications ensuring great filtration. Even better you can use this filter on well water due to the polypropylene material within the string. Simply change out this filter when you notice a change in water pressure. Order yours today!
More Information
Package Qty 1
Used In Brands Hydronix, Tier1
Manufacturer's Id TIER1-SWC-25-1020
UPC 641945742305
Advertised Size (in) 10 x 2-1/2
Media Type Sediment Filter
Media String Wound Polypropylene
Primary Filter Media String-Wound Polypropylene
Filter Life (months) Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x Filter's should be replaced based on usage and filter condition. Filter life is an estimation of expected performance based on typical filtration conditions.x 6 months
Micron Rating (Nominal) The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x The smallest size at which particles are retained by the filter. One micron is equivalent 1/1000th of a millimeter.x 20
Flow Rate (gpm) Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x Flow rate is the volume of water that passes through a filtration system measured in gallons per minute. A filter's flow rate indicates the maximum recommened flow for optimum filter performance. x 5
Warranty Guarantee Unconditional Guarantee for Life of the Product

Reduced Contaminants

The TIER1-SWC-25-1020 reduces the following contaminants:

  • Dirt
  • Hard Scale
  • Rust and Corrosion
  • Sand
  • Silt

Instructions

  1. Turn off water supply. Press red pressure-relief button (if present)
  2. Unscrew housing. Remove large o-ring, wipe clean and set aside
  3. Discard used filter cartridge
  4. Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly
  5. Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly
  6. Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove
  7. NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove
  8. Insert new filter cartridge
  9. Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge
  10. Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation