We use cookies to make your experience better.
Pentek ECP1-20BB Comparable Pleated Sediment Water Filter by Tier1 (20-inch x 4-1/2-inch)
SKU
TIER1-ECP1-20BB
Price $22.99 List Price Price $33.99 Save 32%
Availability: In Stock
Choose a quantity
1 Filter $22.99 -
3 Filters Price $22.29 each -
6 Filters Price $21.59 each
- The 1 micron filter, reduces smaller particles of sand and sediment even rust
- Remember to change once every 6 months
- Great brand at an awesome price
- Large surface area for the best possible filtration
The Pentek ECP1-20BB comparable pleated sediment water filter by Tier1 (20-inch x 4-1/2-inch) is a cost effective filter in comparison to the Pentek brand. Due to the large sized filter of 20x4.5 inches there is more surface area for maximum water filtration power. This 1 micron sediment filter does a great job at filtering out smaller contmainats such as sediment, hard scale, rust and corrosion, and sand. The Tier1-ECP1-20BB works much like the same as the the OEM version, the biggest difference is the savings with purchasing the Tier1 brand. Simply change the filter once every 6 months for optimal performance, and your all set. Order this great filter today!
| Package Qty | 1 |
|---|---|
| Used In Brands | Pentek, Tier1 |
| Manufacturer's Id | ECP1-20BB |
| UPC | 810004472075 |
| Advertised Size (in) | 20 x 4-1/2 |
| Media | Cellulose Polyester |
| Filter Life (months) | 6 months |
| Micron Rating (Nominal) | 1 |
| Operating Temperature (°F) | 40 - 125 |
| Operating Temperature (°C) | 4.4 - 51.7 |
| Flow Rate (gpm) | 20 |
| Flow Rate (lpm) | 75.708 |
| Warranty Guarantee | Unconditional Product Guarantee for Life of the Product |
| Additional Information | End Cap Color: Tan |
Reduced Contaminants
The TIER1-ECP1-20BB reduces the following contaminants:
- Dirt
- Fine Sand
- Hard Scale
- Rust and Corrosion
- Sand
- Sediment
The TIER1-ECP1-20BB is comparable with the following part numbers
| 4PAY4 | |
| 255493-43 |
Instructions
- Turn off water supply. Press red pressure-relief button (if present)
- Unscrew housing. Remove large o-ring, wipe clean and set aside
- Discard used filter cartridge
- Wash housing with dish soap and warm water using a nonabrasive sponge or cloth. Rinse thoroughly
- Fill 1/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly
- Lubricate o-ring with clean silicone grease. Change o-ring if any damage cuts or degradation are present. Insert o-ring in groove
- NOTE: This step is important to ensure a proper housing seal. Make certain the o-ring is seated level in the groove
- Insert new filter cartridge
- Screw housing onto the cap and hand-tighten. Do not over tighten. Make sure cap standpipe slips into cartridge
- Turn on water supply. Press pressure-relief button (if present). Check for leaks before leaving installation
Reset Instructions
Related Products
Pentek ECP1-20BB Pleated Sediment Water Filters (20-inch x 4-1/2-inch)
Price $35.99 List Price Price $51.41 Save 29%
20-BB 1-Inch Whole House Water Filter System
Price $50.99 List Price Price $72.84 Save 29%
WBA Big Blue Housing Mounting Bracket
Price $25.99 List Price Price $36.99 Save 29%
Superb SW-4-SS-8 Filter Housing Wrench - Zinc Plated Steel
Price $27.99 List Price Price $39.99 Save 30%
American Plumber, Culligan, Pentek OR-100 O-Ring for Big Blue Housings
Price $4.99 List Price Price $9.99 Save 50%
O-Ring Silicone Grease (0.2 oz Packet)
Price $4.99 List Price Price $6.99 Save 28%
